Toggle Side Panel
Nu Humanity
Nu Humanity
Close search

Forum Replies Created

  • sha fur

    Member
    March 23, 2017 at 8:14 pm in reply to: Making the Initial water for the cell

    Here is my water prep setup. . .

    Attachments:

  • sha fur

    Member
    March 21, 2017 at 9:52 am in reply to: Making the Initial water for the cell

    I can, and I will, later on this week.

  • sha fur

    Member
    March 21, 2017 at 9:49 am in reply to: Charging water periods

    Well, I am getting a good feeling from the process, maybe a smaller sense of energy from the water. I am more going on physical indicators that the water is progressing to the stage that I can transfer it to my vehicle. The physical indicators that I have seen in the videos. I will keep charging it until I feel I can transfer it to my other cell.

  • sha fur

    Member
    March 19, 2017 at 4:32 am in reply to: Making the Initial water for the cell

    I am currently charging 6 times/day, for 3 minutes, using ~1 amp of power, +-100ma. Any tips on how often to filter the water?

  • sha fur

    Member
    March 19, 2017 at 4:29 am in reply to: Charging water periods

    I am preparing some water and using currently recommended charging times, I believe. 6 times/day, 3 minutes/charging session, using ~1 amp (+-100ma).

  • sha fur

    Member
    March 13, 2017 at 7:18 pm in reply to: Making the Initial water for the cell

    I picked up some spring water off a mountain and charging is now where it should be, 12 volts @ 1 amp. Much easier to get the amperage. Filtered the water once and been thinking of running it through activated charcoal next time, to clean it up even more. There is some little bubbles forming, an insignificant amount, yet, there is some.

  • sha fur

    Member
    March 8, 2017 at 7:59 pm in reply to: Making the Initial water for the cell

    I figured there may be a problem with that mostly unadulterated water. I filtered the water last night and the amperage went down to ~2-3ma. I know where there is some pretty fantastic water, for drinking. I will get some of it and use it instead of deionized water. Until I *do* get it, I will continue to try charging the current water. As soon as I get the new water, and start charging it, I will post info here. Thanks again, Moshe

  • sha fur

    Member
    March 8, 2017 at 1:55 am in reply to: Making the Initial water for the cell

    I am using structured, deionized, water and the variac is cranked up to at least 120 volts going into the Bridge rectifier. I\’m unsure exactly how many volts out of the bridge rectifier, but the amps is less than 300 milliamps. I am guessing there is resistance.

    Potassium chloride. . . . .check.

  • sha fur

    Member
    March 7, 2017 at 11:56 pm in reply to: Making the Initial water for the cell

    Is it still OK to us baking soda to increase amperage to water. Currently I have the variac cranked way up and getting <300ma. I read some information about using baking soda to increase amperage, and it was 4 years old. Just verifying it is OK to use baking soda.

    Shane.

  • sha fur

    Member
    January 18, 2017 at 11:33 am in reply to: Making the Initial water for the cell

    Is the 2\” sphere also isolated from the threaded rod, along with all the rest of the spheres, in both the charging and the car cells, leaving just the bismuth core hooked up to the negative side of the power source? I am currently getting the charging cell hemispheres drilled at the university. I just finished watching a video and it looks like you used a locknut to hold the 2\” sphere in place which may also isolate the 2\” sphere.

  • sha fur

    Member
    January 8, 2017 at 9:15 pm in reply to: Making the Initial water for the cell

    Alrighty. I managed to pick up a couple different kinds of capacitors:

    -140000uf 40v – I figure I can use this one, being careful to avoid exceeding 40v from the variac.
    -820uf 200v – overkill but….. 😉

    I now have all the components to get started making some water. Now, I just have to clean up one of the moejoe cells and start making the second one. The local university has all the fancy drilling tools and may be willing to assist me. Will be contacting them soon. I will keep everyone in the loop as I go. It will be slow, though. Heads up.

  • sha fur

    Member
    January 8, 2017 at 9:03 pm in reply to: Making the Initial water for the cell

    \”A cut plant will have a much longer life span in a vase if a ground wire is added to it, because it will simulate a similar grounded/Earth connected environment for the plant to live in and allows for an electrical connection that the plant needs to live!\”

    Well, this is new information to me!! Thanks Bryce.

  • sha fur

    Member
    December 31, 2016 at 10:50 pm in reply to: Making the Initial water for the cell

    Thanks Moshe. I am going to see if I can get one in town today.

  • sha fur

    Member
    July 28, 2016 at 10:27 am in reply to: Instructions for Moe-Joe Installation.
    quote :

    That\’s good that you left them alone. There have been some attempted tweaks but mostly just leaving trouble after with the sensors and not much for results.
    What info are you referring to though?

    The other info was just using the Moe-Joe cell with no modifications to the vehicle.

    quote :

    Now we have to troubleshoot.
    Can you take a few pics of your installation? Post them in a reply here.

    Where did you charge the water?
    How is your cell in the car? did you do any precharging on that?

    What car are you driving? Year? Make, model?

    I will answer this in more detail as time permits, and when I find the pix.

    Shane.

  • sha fur

    Member
    July 27, 2016 at 7:57 pm in reply to: The Challenge of EFIs the moe-joe cell + solutions

    What kind of success did the VOLO produce for you, Moshe? I see no report of findings in this thread.