Rob Eklund
Forum Replies Created
-
Ok i do have a 4×4 sheet of plexiglass at 1/4 inch thick. It should be acrylic. I think I have a roll of shim stock around here somewhere that is 316 stainless at .004\” I\’ll see if I can cut them into 12\” squares (plexi) an 11\” squares (stainless).
At least there was a noticible effect, the corona wire I am using is also stainless (TiG welding wire) held up on glass rods. for the first try positive over the cell, negative just off the ceramic table at the base.
-
Well I tried the aluminum foil inside page protectors (plastic sleeves that school papers go in).
It did indeed have a big effect on how the cell felt, but I cant say it was a good one. It did build up a charge my arm hairs would stand up when near it (like walking in front of a crt tv screen). But it did not feel \”good\” to be around if that makes sense.
Right now I am not sure if the materials need to change, how it is applied needs to,or if if just isn\’t a good idea, my first guess is to get rid of the plastic in favor of glass, or thick paper. glass should be a better insulator so I will start there.
-
Just checking, what would you think of repurposing a trumpet or bugle if one could be found at a garagesale type of situation? The shape seems about right.
-
This is what I am playing with now, it is that vodka bottle made into a vortexer, that also works as the lid for the dispensing jar.
It is still a work in progess, but it does seem to charge the water. With tap water it does start out with a cone underneath, after it runs for a hour or two it becomes a stream.
-
One other idea, I am going to go out to a craft store to buy some sheets of pvc and a roll of acetate. If we layer either pvc, or acetate sheets with aluminum foil it would make a high voltage capacitor.
If we put that under the cell (or truck tires)with the + end connected to a corona wire. the – end is what is have to play with to figure out, do you think it would go to earth ground, under the cell(or the tires), or a lower corona wire relative to the \”+\”, just around the base?
-
I wouldn\’t think either or both even would solve it, just an attempt to stack resistors in a way.
-
Would the size of the tire make a difference, I am using 44\” tires on 16.5\” rims? That is a lot of rubber to go through.
On a second line of thought, do you think a ceramic coated spacer between the brakes and the rim, and on the lugnuts might help? ceramic has been used as a high voltage insulater for a long time and it would take the heat from the brakes easily. I know it wouldn\’t totally solve the issue, but it may ease it somewhat.
-
I was thinking that while getting the vehicle prepared for the cell, it may be possible to raise the earth refence to that of the cell to temporarily discourage it draining.
I have read about a few ways to get power levels similar to the ones he is talking about in his unit charge, directly from the earth, only apart from novelty this would be the first real use for it I have heard of.
From what I understand, once the charge gets set in it is not nearly as fragile. In the case of my truck the only real electronics to be worried about getting damaged is the radio, so it may be worth a try.
-
I was thinking that while getting the vehicle prepared for the cell, it may be possible to raise the earth refence to that of the cell to temporarily discourage it draining.
I have read about a few ways to get power levels similar to the ones he is talking about in his unit charge, directly from the earth, only apart from novelty this would be the first real use for it I have heard of.
From what I understand, once the charge gets set in it is not nearly as fragile. In the case of my truck the only real electronics to be worried about getting damaged is the radio, so it may be worth a try.
-
I have heard that thunderstorms can greatly effect the way a joe cell \”in this case\” works with a vehical. I wonder if that would have something to do with the earth voltages being higher? I have read somewhere that during a thunderstorm the earth can be charged in the area of 2000 volts per square meter.
I wonder if that would be high enough to negate the \”bleeding\” voltage to ground long enough for the unit charge to \”settle in\”?
I was curious about a frequency to see if it may tie into some of the work that Tesla did on wireless power and energy transmission. Along with some of the observations by Schumann on earth frequencies.
-
I am just curious, do you know if he ever has checked the area of the unit charge field for a frequency? I am beginning to think (at least in the case I have) that the bowl is serving a type of antenna/reflector combination. If there is a frequency to it, it should be possible to somewhat tune it by the size, shape, and position of the \”antenna\” in relation to the cell,to find a better resonance with the truck/car/motorcycle, or even for healing purposes.
-
I am just curious, do you know if he ever has checked the area of the unit charge field for a frequency? I am beginning to think (at least in the case I have) that the bowl is serving a type of antenna/reflector combination. If there is a frequency to it, it should be possible to somewhat tune it by the size, shape, and position of the \”antenna\” in relation to the cell,to find a better resonance with the truck/car/motorcycle, or even for healing purposes.
-
I would guess the poles may change according to what you may need, I have been told by several people that I am the most easy going person they have ever met. whith that said it seems to work good for me. I think its a matter of finding what works for whoever is drinking it. My daughter likes it better with a balance towards south poles as well.
-
A view of the vortex in action.
Attachments:
-
I found a bottle that seems to work very well for these (Just started my first batch, but it seems to work very well for creating a vortex.
The bottle comes with some french vodka in it the brand is called Chambord, it has a upper part that came the closest to the shape that I have found locally. And it has a magnet of some sort in the cap already, I carefully drilled a .25\” (6.35mm) hole in it and am using a repurposed pump from a decrotive fountain for now. I also put some n50 magnets alternating poles, around the neck.
Attachments:
