[Elianodi Eliano]

Hey daniel,

so I can only upoload one pic for each post. I thought I can upload more then one.

Beautiful schematics.
Sharing information is what will move our consciousness forward. 🙂

will start to charge my water soon with those circuits.

For the Meissner circuit, the modified version is best of course, because the 100ohm will consume some power, so removing it is best.
The capacitor need to be AC, or Non-polarized one, rating 100V or higher, just for protection.

Air-core coils are best because there is No hysteresis losses and eddy currents in the steel at higher frequencies.

with these circuits, you can also make Nano-sized particles of colloidal Silver (tested by Peter Lindemann) for CS consumers. Just hook your electrodes in distilled water instead of a battery and hit the button.

Waiting for the Feedback of the results.
Cheers to all

[Elianodi Eliano]

Hey Daniel,

Yes this is the Youtube video, but the version that is not meant for HHO cells, or Now for MOE-JOE :hopefully 😀

For the Bedini, I was putting my digital meter to DC voltage measure, not AC, while charging, I will experiment with this more in the coming days.

Man, I\’ll send you the pix , dunno why it\’s not working here to post the pix, then you can post them for me 🙂

Check out Ritalie.com, this is the dude that I bought his material, he has videos for his HHO charging with the MEissner circuit,and what a beautiful charge, always in resonnance, the 100ohm resistor is not necessary with HHO, it looses power.

Check your email Dude, excited to apply this to Moe-joe.

Cheers MAn

[Elianodi Eliano]

Hey again Daniel,

Thank you for your advices. 🙂

Also, I\’d love to see the schematic of the bedinin charger Solid state

Sure, I have a simple one, the bedini solid state simplified to a transistor, couple of resistor and a bifilar coil.
Here it is attached.

I didn\’t test it on my Moe-Joe yet, I am charging a small battery now, actually conditioning it and it\’s taking lots of time. Soon I\’ll hook it up to my Moe-joe-

But what\’s interesting is that I used this circuit to make Colloidal Silver, it was recommended by Lindemann.
So what happened is that the voltage on the output raised increasingly to 2.2V and stayed there the whole time, with soooo little black spots on the silver rods. The water very clear. According to Lindemann, this will produce Nano-Particles. Also after I turned off the circuit, a residual voltage of 0.36 V was measured across the cell, pretty interesting as well. (Maybe the Silver is by itself a good Orgone energy attractor ??? It\’s good to experiment with Moe-joe with Nano-particles of Silver added to the water). The water used was just distilled, with no energysing for it what so ever.

Now what\’s moooore intersting, is that the HHO cell dudes, are using a self resonating charger, called Meissner Circuit. It will adapt to the cell continuously, in terms of amplitude of the pulses and frequency. Pretty amazing dude, energy efficient, and intelligent. And the schematics are very simple to make. In an hour or two, you\’ll be running your Moe-Joe on it. They too condition their cells to have this white scum on the plates, which takes to form for hundreds of hours, but then they can condition even tap water in two hours or so. There is a modified Meissner Schematic,works perfectly, that I found in a book I bought from a dude experimenting with radiant energy, an experimented mechanic person. I don\’t know if I am allowed to share here, let me know if it\’s okay with you. I think this charger will make a difference for Moe-joe.

I am not sure if this bedini circuit is adjusting its frequency with the battery with time, I need to have some better tools to measure, but yesterday, I measured a pulse of 20khz on my digital meter.
Did the battery initial conditioning take a long time with you?

[Elianodi Eliano]

Hey Moshe,

I made the improvement to the cell as you suggested.
I also changed the water and replaced it with new fresh one. Its all clear now and much beautiful.

Also noticed while cleaning that there were a lot of brownish residues on the spheres, and the the inner one that you said to be polished is covered with grayish material, I think it\’s from the electolysis, and all the spheres as well, does this affect the Orgone Charging process ?

Also the uper bolts are totally covered with plastic now, but I noticed that when the bubbles comes out, the automatically attracted to the middle negative bolt, eventhough it is isolated now.

---

Attachments:

[Elianodi Eliano]

Hey Moshe,

So happy to hear your feedback.
And amazed by how you could sense my intentions and the energy around my cell, your talented Bro.

I\’ll make sure your suggestions are done today,
and will report ASAP about the results !

Through your own experience with MObius coils and your car Mobius lol, how there presence around a crystal affect the orgone emission of the crystal ??

And have been thinking about something, if I download my crsytal with a certain program or thought form, and excite the mobius coil with a certain frequency (eg. 528hz) will that help to emit an orgone energy that carries my intentions and transmit to the target that will absorb the Orgone ?

[Elianodi Eliano]

Hey Moshe,

Kindly find attached a zip file of 3 photos of my MOe joe setup.

The colored piece is an Orgonite, with a Clear Quartz Crystal in the middle, and also surrounded by Clear Quartz with Mobius Coils in closed loop circuit each(What do you think about mobius coils and crystals around MOe Joe).

Also I noticed that the Brownish color is very strong, could it be because initially I had the cell charge with a current higher than 1amp ? and I am sure I did it.

How could I charge the cell with a 12V source in terms of time and Sets per day .

Also the Bismuth core came with two stainless steel bolts and in the videos u posted it comes with one stainless and one plastic.

Also I guess my water should be more in quantity from the top of the cell ?? The stainless bolt will be totally immerged at that point, how can I do that without letting the metal of the contact Node dissolve because of the electrolysis ?

Thank you Bro 🙂

[Elianodi Eliano]

Well Moshe,

thanks for your reply.

Since this energy is being attracted to the ignition coil spark, this spark must be behaving like a high
density orgone charge (Or whatever it is ).
Reich always said that Orgone has a blue radiation,
and the spark of the coil or the flame of a stove
is a blue as well. This is an open discussion of course,
but if we need to shoot orgone to water or to a sick
body part, is it sufficient to meditate and ask the cell
to fill the object or organ with orgone energy ?

On the other hand, if I have a small half horse power
water pump, 370W running 4 meters away from the Moe-joe,
will this affect the Quality of the energy accumulated
by the cell ? Can\’t this be easily overcome by surrounding the cell with orgonite, the one\’s made
by Don Croft, or Orgone generators as well ?