Dear Moshe,

Thank you for kind reply..

Recently, I have charged the ground water during several days (more than 6 days) with 1 amps to apply to car kit.
When I analyse it there are Fe, Cr, Ni components in charged water even though I could not know the concentration of components.

To understand and install Moe-Joe Cell for Car kit,… Read more

Hi Moshe,

Thank you for your nice comments.

I very appreciate your kind comments to me everytimes.. :laugh:

You said that ” no. the bismuth core shouldn’t create any scum because it is coated in goop / silicone and is not in contact with the water.
that yellow discoloration is due to nickle and iron coming into the water.… Read more

Hi Moshe,

Thank you so much for your nice comments…

I did the water charging with 1 amp during 2.5 day with VARIAC (Method 1).

I poured the water inside Moe-Joe Cell out. and I found that yellow some particles exist in water. I guess that it come from some Bismuth core.. is it right?

In official web site, you mentioned… Read more

Hi Moshe,

Thank you very much for your kind reply..

You said that “very very low would be 0.01 amps, like 10 mA.
0.1 amps = 100 mAs and it is low, but not very very low.”

I measured the currents with different controlled volatage that Moe-Joe Cell device with connected conventional DC charging with VARIAC and bridge rectifyer -… Read more

Hi, Moshe,

Thank you very much for kind reply.

In your comments, you said that “so start small and observe the water.
feel the water. do you sense the energy in the water?
do you see an increase in surface tension?”
I want to know how to feel and observe the charged water in detail.
for example, If I touch it, can I feel the… Read more

Dear Moshe, Sir,

Thank you for kind reply..

Finally, I have a success about bubbling formation!

Another questions is below…

You mentioned that “yes, you can use baking soda also to increase the current.
then, you must use shorter charging times.
don’t charge longer than 3-5 minutes at a time.”

I have set up Moe-Joe Cell… Read more

Thank you for your kind helps.

Another question is below..

I used the distilled water for water changing. Is it ok? Is it possible that it flows the current in distilled water? What kind of water can you recommend it?
Is it possible to use tap water for checking the bubbles or water charging? (instead of distilled water) (I heard that… Read more

You said that ” it is better to put the nylon cap over the head of the +ve bolt on the inside of the 5″ hemisphere. it will keep all the electricity insulated only to the 5″ hemisphere and not to the head of the bolt, which would otherwise make it the closest element to the inner 2″ -ve sphere.”

I cannot understand all your reply. Could… Read more

quote :Dear Moshe,

THANK you so much!!!

I will try to do the experiment as you told me.

my attached a zip file (image file) is related on the connection of + stainless bolt inside outside the spacer. Please check it whethere the set-up of connection of + stainless bolt is well done or not.
Awaiting your reply.. If you check this,… Read more

I think that our VARIAC and wire etc. are ok. Only problem is something wrong inside Moe-Joe Cell concerning a electric short. To solve the short problem, we checked the electrical esistant (ohms).

There is a short problem somewhere. So, we seperated all part of Moe-joe Cell.
After that, we checked the electrical resistant (Ohms) as… Read more

Thank you.

I still did not solve the high current problem.
(I think that 1 AMP can not be controlled by using our VARIAC. Anyway I should do solve this problem to see bubbling and/or scum from Moe-Joe cell)
(As you mentioned it the important thing is 1 AMP control to check bubbling and/or scum (come out).)
*What is the difference… Read more

Here is the picture of my setup:

I didn’t use KOH solution I just used only distilled water.

But I could not get 1 AMP. anyway I try to adjust 1AMP.

Please check the picture..

Attachments: