MemberFebruary 12, 2020 at 10:33 am
sorry for my broken English. :blush: :blush: I\’m get the moe joe cell.Ca you explain please hau I have to charge the water for stage 3 please. 1)Haw many vot and amp,I can use car battery or I can using a car battery charger.
2) Abaut time for charging it\’s 10min.5time for 24 hours 3)I have to polish the cell before to charging the water 4)The vessel have to be glass, metal or plastic 5) Hau many days have to charge the water Thanks Victor
MemberFebruary 13, 2020 at 2:41 am
Victor Cosan wrote:quote :
Go to this page –
Go to Method 1 – Conventional DC charging with VARIAC and bridge rectifyer – this will help you achieve stage 3. but stage 3 is not so important. it is just looking like a lot of bubbles. you can prepare and create excellent water using just 24Volts DC batteries.quote :
don\’t use a car battery charger
you can use car battery (or two car batteries in series – to make 24V)
and if you add potassium chloride salt to the water, you can get to 1 amp with
either 12 volts or 24 volts. with 24 volts you will obviously need less salt to achieve 1amp of current.quote :
on the same page, see here:
c) Turn on the VARIAC so that the current begins flowing. Adjust the VOLTAGE on the VARIAC to around 60-80 volts AC, so that the current reads close to 1 AMP. Charge for 1-3 minutes 4-6 times /day until the water gets filled with a brownish, orangy fluffy \”scum.\” then filter the water, using 2 Blue Shop towels (available at Home Depot)
And also below.quote :
Glass. Look at this page again and see the glass jar –
now, i use diamond drill bits to make the bottom hole.
no. it\’s not necessary. but it looks nicer. 🙂 and it *may* be a little better.quote :
Glass. Only glass.quote :
start with charging a few days. 2-3 days.
see how the water feels.
if you cannot \’feel\’ the orgone energy in the water,
then test the potential difference across the cell with no
MemberFebruary 13, 2020 at 9:33 am
Thanks Daniel for help. 🙂
MemberFebruary 13, 2020 at 10:02 am
Sorry man I can put the cell to the diesel ingen for example audi a4 1.9 tdi
MemberFebruary 14, 2020 at 1:18 am
yes, you can try it. diesel is different of course than regular fuel engine.
But you can try and see how it goes. I cannot say absolutely yes or no.
you may see fuel mileage improvement or boost in engine performance or more power or…
ALL of the above? Let us know how it goes.
MemberFebruary 14, 2020 at 7:38 am
Ok I will let you know,Saturday I start to charging the water and Tuesday I install the moe Joe cell to the petrol or diesel engine and I let you know. For stage 2 the car it\’s running in petrol and orgoniu from moe joe cell. For stage 3 only in energy from moe joe cell I have to disconnect the petrol pump. Can you explain please hau correct I have to using or to install the moe joe cell,stage 2,stage 3,for my car. Mitsubishi Lancers 2.0 petrol.audi a4 1.9 t.d.i. Thanks for halp 🙂
MemberFebruary 15, 2020 at 3:16 am
Victor Cosan wrote:quote :
Victor, a lot of this technology is still experimental.
Here are some things you can consider.
For some instructions:
Please read through the forums.
Also check out the different pages and videos a
watch this video –
MemberFebruary 18, 2020 at 1:10 pm
:cheer: Hi Daniel I finished to polish the moe-joe cell. It\’s charging 2 days. Hire it\’s a photo
MemberFebruary 18, 2020 at 1:12 pm
Sorry man, can\’t make it, I can\’t send you the photo wen I chearghing the water I have to disconnect + and – or I have to live – connected. Thanks Can you explain please hau have to put the photo to show you wat I did Thanks.
MemberFebruary 18, 2020 at 7:39 pm
MemberFebruary 18, 2020 at 7:54 pm
Sorry man it\’s not working what a obout when I charge the water, do I have to disconnect the negative and positive, or I have to live the negative in ( connect)
MemberFebruary 21, 2020 at 6:48 pm
MemberFebruary 21, 2020 at 7:24 pm
hey!! beautiful polishing job.
how did you do the polishing?quote :
while you charge, you have to leave both the negative and positive connected.
when you are NOT charging, so in between the charges, you leave just the negative connected.
MemberFebruary 21, 2020 at 7:28 pm
I was polish with drill and some paste for pollish. Thanks for the information you give me 🙂
Log in to reply.